Skip to Content

Your Favorites

  • HOMAX<sup>®</sup> TEX»PRO<sup>™</sup> Interior Texture System

HOMAX® TEX»PRO™ Interior Texture System

View Data Sheets
Size

Each (EA)

Find a Store
Are you a pro? Use our new online ordering tool.
Pro opening paint can

Product Details

Up to 70% faster1 and 60% lighter2 than a traditional hopper gun, Homax TexPro Texture System makes a tough job simple. With a lightweight, comfortable and innovative design, applying texture is now a breeze. Simply hook the sprayer up to an air compressor*, load the ready mix texture cartridge, and pull the trigger. Faster >> Lighter >> Better. A Simpler Texture System2.

  • Innovative alternative to hopper gun
  • Comfort, balanced grip
  • Easy, ready-to-use cartridges* makes jobs easy to tackle with one person
  • Quick and easy prep and cleanup
  • Delivers consistent, quality results
  • Two texture formulas* air pressure settings and spray tip options enable a wide range of texture looks
  • Applies light and heavy texture to interior walls and ceilings
  • For use on indoor drywall
  • Only for use with HOMAX TEXPRO Texture Cartridges*

*sold separately

1Setup and cleanup time for HOMAX TEXPRO vs. hopper gun

2HOMAX TEXPRO vs. full hopper gun

Features:

  • Innovative alternative to hopper gun
  • Comfort, balanced grip
  • Quick and easy prep and cleanup
  • Delivers consistent, quality results
  • Applies light and heavy texture to interior walls and ceilings
  • For use on indoor drywall

Product Feature

Homax TexPro Sprayer; Rear Gasket (2); Front Nozzle Gasket (2); Air Shut-Off Valve; 3 Spray Tips (small, medium, large); Rubber Spray Tip Cover; Cartridge Seal Cutting Tool; Cleaning Brush; Small Storage Case with Spare Hinge Pins; Instruction Manual

Application Details

TexPro Texture System operates differently than a typical hopper gun–take time to understand how it works and practice using this new system before you attempt your first job.

  1. Set up sprayer
  • Install front gasket in front cap; install rear gasket in rear cap; select & install spray tip; connect air shut-off valve & set to off position

2. Inspect sprayer before every use

  • See user manual for step-by-step instruction with photos.

3. Choose a texture cartridge

  • Select light or heavy texture for desired appearance & job conditions

4. Prepare cartridge

  • Cut cartridge tip; puncture seal inside tip

5. Load cartridge

  • With air shut-off valve “off”, compressor power disconnected, and front cap latched closed – load cartridge: Open rear cap. Insert prepared cartridge.

6. Setup compressor

  • Use a compressor (sold separately) that delivers 2.6 scfm or greater; higher compressor pressure = finer splatter patterns; lower compressor pressure = heavier splatter

7. Prepare to spray

  • Put on protective wear. Protect surroundings from overspray. Prepare surface for texture following instructions on texture cartridge.

8. Start to spray

  • Start compressor and turn air shut-off valve to on position. Begin spraying holding sprayer tip 4 feet from wall. Control size of texture pattern by a choice of spray tip, compressor output pressure, and sprayer regulator pressure.

9. Stopping spray

  • Release trigger. After releasing trigger, spray will continue from nozzle for 3 seconds. Ensure sprayer is pointed at surface until spray completely stops.

10. Cleaning

  • After use, disconnect power to air compressor and remove components. Clean each component. Allow parts to dry before replacing in case.


WARNING: BEFORE HANDLING THE TEXTURE SPRAYER OR WHEN YOU STOP SPRAYING OR ARE REMOVING ANY EQUIPMENT PARTS:

1. SHUT OFF AIR SOURCE AT AIR COMPRESSOR
2. DISCONNECT AIR COMPRESSOR POWER SOURCE

Looking for a datasheet? Access PPG's full datasheet portal here or visit https://products.ppgac.com/

Code Sizes Download
TP01 Each (EA) N/A