PROLUXE® Maintenance RE Wood Finish

Size

Gallon, 5 Gallon

Sheen

Clear

Product Details

A premium, non-pigmented exterior finish to be used exclusively over existing PROLUXE® 23 Top Coat RE Wood Finish or PROLUXE® Log & Siding Wood Finish as a maintenance coat.

Features:

  • Revives Satin Sheen and Water-Repellency of the previous finish
  • Provides a Mildew-Resistant Finish
  • Powerful UV Absorbers Protect Color and Wood Substrate

Area Preparation

GENERAL SURFACE PREPARATION: All wood surfaces must be thoroughly clean, dry and free of dirt, grease, grime, mildew, mill glaze before applying Maintenance RE Wood Finish. Cleaning Recommendations 1. Spray all wood surfaces with clean water, completely wetting the wood. 2. Working from bottom to top, generously apply a cleaning solution of four (2) ounces of 100% powdered Tri-Sodium Phosphate (TSP) or phosphate-free substitute with one (1) quart of liquid bleach and three (3) quarts of water to the wood surfaces with a garden sprayer or a heavy nap roller cover. 3. Let the solution dwell on the wood for 15-20 minutes as you scrub the surface with a hard bristle brush to help remove mill glaze or weathering. Do not allow solution to dry on the wood surface. 4. Working from bottom to top, power wash cleaning solution from the wood with plenty of clean fresh water using 500-800 psi with the nozzle 8-12 inches from the surface for full effectiveness of the cleaning and to prevent damage to the wood. 5. Allow the surface to dry for 48 hours, or to have a moisture content of 18% or less before finishing.  Maintenance RE Wood Finish should be applied within four weeks for vertical surfaces (siding), provided that the surface remains free of dirt, grease grim, mildew.   Warning! If you scrape, sand or remove old paint, you may release lead dust or fumes.  LEAD IS TOXIC.  EXPOSURE TO LEAD DUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN,  PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.  Wear a properly fitted, NIOSH-approved respirator and prevent skin contact to control lead exposure.  Clean up carefully with a HEPA vacuum and a wet mop.  Befor you start, find ou thow to protect yourself and your familiy by contacting the USEPA National Lead Information Hotline at 1-800-0424-LEAD or log on to www.epa.gov/lead.  Follow these instructions to control exposure to other hazardous substances that may be released during surface preparation. 

Application Details

1. Buy sufficient product for the whole job and intermix all product together before starting to avoid color variance. 2. Stir thoroughly before and periodically during application. 3. Do not thin. 4. Apply when air and surface temperature is between 50° F (10° C) - 90° F (32° C). 5. Do not apply in direct sunlight, if rain, snow, heavy dew or low temperatures below 40° F (4° C) are expected within 48 hours. 6. Brushing is the preferred method of application, using a natural bristle brush, If applied by roller or airless sprayer, back brush immediately to ensure penetration and to avoid an uneven finish. For airless spray, use a .009”-.011” tip at 700 - 800 psi, adjust pressure as needed. 7. Apply one even coat of Maintenance RE Wood Finish, avoiding heavy application. 8. Apply in the direction of the grain. 9. To avoid lap marks, start at one edge and follow through to the end of each board maintaining a wet edge. 10. Coat all end grains and the back of all boards if possible.

Drying Time

Dries to touch in approximately 6 hours. Dries to hard cure in 24-48 hours. Low temperature, high humidity, thick films or poor ventilation will increase these times. Avoid heavy abrasions immediately following application

Coverage

On properly prepared surfaces, 400-500 sq ft/gallon (10-11 m2 /L). Actual coverage may vary depending on the type, age and texture of the wood and application method.

Cleanup

Clean tools immediately with mineral spirits. Clean spills right away with a damp cloth.

Product Warning

DANGER! COMBUSTIBLE LIQUID AND VAPOR. HARMFUL IF INHALED. HARMFUL IF ABSORBED THROUGH SKIN. HARMFUL OR FATAL IF SWALLOWED. CAUSES RESPIRATORY TRACT, EYE AND SKIN IRRITATION. Sanding and grinding dusts may be harmful if inhaled. Inhalation of high concentrations of vapor may affect the central nervous system. Repeated exposure to high vapor concentrations may cause irritation of the respiratory system and permanent brain and nervous system damage. High vapor concentrations can cause headaches, dizziness, drowsiness and nausea and may lead to unconsciousness. Can enter lungs and cause damage. Keep away from heat and flame. Do not breathe vapor or mist. Do not swallow. Do not get on skin or clothing. Avoid contact with eyes. Keep container tightly closed and sealed until ready for use. Wash thoroughly after handling. Provide fresh air ventilation during and after application and drying. Avoid the inhalation of dust, particulates, spray or mist arising from the application of this preparation. Use personal protective equipment as required. DANGER - RAGS, STEEL WOOL OR WASTE SOAKED WITH MAINTENANCE RE MAY SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED WATER-FILLED METAL CONTAINER. Note: These warnings encompass the product series. Prior to use, read and follow product-specific MSDS and label information. FIRST AID: If swallowed, rinse mouth with water (only if the person is conscious). Call physician immediately. Do not induce vomiting unless directed to do so by medical personnel. If in eyes, rinse with water for 15 minutes. Check for and remove any contact lenses. In case of contact, immediately flush skin with plenty of water while removing contaminated clothing and shoes. Get medical attention immediately. If inhaled, remove to fresh air. Call physician immediately. Keep out of the reach of children. For workplace use, an MSDS is available from your retailer or by calling (412) 492-5555. EMERGENCY SPILL INFORMATION: (412) 434-4515 (U.S.).

Code Finish Base Sizes Download
SIK61003 Clear Clear Finish Gallon, 5 Gallon
SIK61003C Clear Clear Finish 5 Gallon, Gallon, Gallon
  • OTC
  • LADCO
  • US National AIM
  • CARB 2000 SCM
  • Canada National AIM