PROLUXE® SRD Semi-Transparent Wood Finish

Size

5 Gallon, Gallon

Sheen

Semi-Transparent

Product Details

One-coat penetrating semi-transparent wood stain with UV absorbers for a boost of UV protection for less frequent maintenance.  

Features:

  • One Coat Semi-Transparent Matte Finish
  • Strong water repellency and UV protection
  • Tintable to a wide range of color options

Area Preparation

All wood surfaces must be thoroughly clean, dry and free of dirt, grease, grim, mildew, mill glaze and previous coatings before application. Spray all wood surfaces with clean water, completely wetting the wood. Apply a cleaning solution of four (4) ounces of 100% powdered Tri-Sodium Phosphate (TSP) or phosphatefree substitute with one (1) quart of liquid bleach and three (3) quarts of water to the wood surfaces with a garden sprayer or a heavy nap roller cover. Scrub surface with a hard bristle brush for 15-20 minutes to help remove mill glaze or weathering. Do not allow solution to dry on the wood surface. Power-wash wood surface clean with fresh water using 500- 800 psi with the nozzle 8-12 inches away to remove cleaning solution. Allow the surface to dry for 48 hours, or to have a moisture content of 18% or less before application. Sand all cleaned wood using 80-120 grit sandpaper for vertical surfaces and 60-80 grit sandpaper for horizontal surfaces. Always sand in direction of the wood grain and remove sanding dust. Finish should be applied within one week of preparation for horizontal surfaces (decks) and four weeks for vertical surfaces (siding), provided that the surface remains free of dirt, grease, grim and mildew.  Warning! If you scrape, sand or remove old paint, you may release lead dust or fumes.  LEAD IS TOXIC.  EXPOSURE TO LEAD DUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN,  PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.  Wear a properly fitted, NIOSH-approved respirator and prevent skin contact to control lead exposure.  Clean up carefully with a HEPA vacuum and a wet mop.  Befor you start, find ou thow to protect yourself and your familiy by contacting the USEPA National Lead Information Hotline at 1-800-0424-LEAD or log on to www.epa.gov/lead.  Follow these instructions to control exposure to other hazardous substances that may be released during surface preparation. 

Application Details

CAUTION: Surfaces are slippery when wet. Use caution when walking on wet surfaces during application. Test wood for absorbency by sprinkling water on the surface – if water is absorbed within 30 sec. - 2 min., depending on climate, the surface is ready for finishing. If water is not absorbed, wait 30 days and re-test. Before starting, test your color choice on a small area. Buy sufficient product for the whole job. Intermix all product together before starting to avoid color variance. Stir thoroughly before and during application. Do not thin. Apply when air and surface temperature is between 50° F (10° C) - 90° F (32° C). Do not apply in direct sunlight, if rain, snow, heavy dew or low temperatures below 40° F (4° C) are expected within 48 hours. Application using a natural bristle brush is the preferred method. If applied by roller or airless sprayer, back brush immediately to ensure penetration and to avoid an uneven finish. For airless spray, use a .011”-.015” tip at 700 - 800 psi, adjust pressure as needed. Apply only one even coat, in the direction of the grain avoiding heavy application. To avoid lap marks, start at one edge and follow through to the end of each board, maintaining a wet edge. Coat all end grains and the back of all boards if possible.

Drying Time

Dries to touch in approximately 4 hours. Dries to light foot traffic in 24 hrs

Coverage

On rough and weathered surfaces, 150-250 sq ft/gallon (4-6 m2 /L). On smooth surfaces or hardwoods, 300-400 sq ft/gallon (7 - 10m2 /L). Actual coverage may vary depending on the type, age and texture of the wood and application method.

Cleanup

Clean hands and tools immediately with warm, soapy water. Clean spills right away with a damp cloth. To maintain the products protective characteristics, apply a maintenance coat when visibly required.

Product Warning

Provide fresh air ventilation during and after application and drying. Avoid the inhalation of dust, particulates, spray or mist arising from the application of this preparation. Use personal protective equipment as required. DANGER - RAGS, STEEL WOOL OR WASTE SOAKED WITH SRD SEMITRANSPARENT

MAY SPONTANEOUSLY CATCH FIRE IF IMPROPERLY DISCARDED. IMMEDIATELY AFTER EACH USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED WATER-FILLED METAL CONTAINER. Note: These warnings encompass the product series. Prior to use, read and follow product-specific MSDS and label information. FIRST AID: If swallowed, rinse mouth with water (only if the person is conscious). Call physician immediately. Do not induce vomiting unless directed to do so by medical personnel. If in eyes, rinse with water for 15 minutes. Check for and remove any contact lenses. If on skin, rinse well with water. Wash with soap and water. Get medical attention if irritation develops. If inhaled, remove to fresh air. If experiencing respiratory symptoms call a POISON CENTER or doctor/physician. Keep out of the reach of children. For workplace use, an MSDS is available from your retailer or by calling (412) 492-5555. EMERGENCY SPILL INFORMATION: (412) 434-4515 (U.S.).

Code Finish Base Sizes Download
SIK500-190 Semi-Transparent NEUTRAL/ACCENT/ULTRADEEP/CLEAR 5 Gallon, Gallon
  • OTC
  • LADCO
  • US National AIM
  • MPI
  • SCAQMD
  • CARB 2000 SCM
  • Canada National AIM